What addresses stay the same in this situation, and what addresses change? This activity will examine device configurations in Packet Tracer, select the proper cable based on the configuration, and connect the devices. This activity will also explore the physical view of the network in Packet Tracer. Step 1: Connect the devices. Click on router R2-Central and examine the configuration using the Config tab. Click on both routers and examine the configuration using the Config tab. Connect the routers together using the proper interfaces and the proper cable Click on router R1-ISP and examine the configuration using the Config tab.
Connect the proper interface on the router to the proper interface on Eagle Server using the proper cable. Step 2: Verify connectivity. If the pings fail, check your connections and troubleshoot until the pings succeeds.
Check your configuration by clicking the Check Results button. Step 1: Enter and view the Physical Workspace. Most of our work in Packet Tracer has been done in the Logical Workspace.
In an internetwork, routers maybe in different sites from across the street to across the globe. The DCE connects to a service provider's local loop and the connections are repeated at the other end of the link. The Physical Workspace allows us to see these relationships more clearly. Step 2: View the standard lab setup at the various levels of the Physical Workspace.
Click on the Central City, it shows the city and the location of the Central Office building. Click on the Central Office building, it shows the floor plan of the building and the location of the Wiring Closet.
Click on the Wiring Closet, it shows a physical representation of the equipment installed in the wiring closet and the cabling that connects the equipment. Examine this view of the topology. Click on Intercity on the Navigation bar.
Repeat the steps to view the equipment installed in ISP City. You must provide for the three existing networks. Set all Ethernet interfaces to auto negotiate speed and duplex which will achieve Full Duplex, Mbps operation, if both ends of the link can support it.
For all devices, make sure the power is on to the device and to the interfaces make sure the Ethernet interfaces are not shut down.
Use the highest usable subnet address as the gateway and assign the two lowest usable addresses to the PCs. These procedures were explained in the Chapter 5 and 6 Skills Integration Challenges. Compare and contrast the serial connection with Ethernet.
In a future course you will learn much more about switched Ethernet technologies. Device names and routing have already been configured. Task 1: Build the Network Topology. Use the following charts, and the devices in the Device Pool, to create the topology. You are asked to use the Seven total networks are required; assign the networks in decreasing order of number of hosts required for efficient use of address space.
Task 3: Interface Configuration Perform interface configuration of the R1, R2, and R3 routers, the PCs, and the server according to the addressing scheme above. You have also developed conceptual understandings of networking protocols and device algorithms.
Here is an opportunity to test yourself: see if you can complete the entire challenge approximately configurable components, though some are quite easy in under 30 minutes. Task 1: Plan. Note that both the Display names AND host names for all devices must be configured exactly, and in general all strings names, passwords, banners should be typed exactly as specified in these instructions, for the grading to work properly.
Task 2: Build and Configure the Network. Build the network, taking care to make connections as specified. Configure both routers, the switch, the server, and the two PCs. Configure the routers using the CLI to practice your skills. The router configuration must include "housekeeping" display name, hostname, passwords, banner , interfaces Fast Ethernet and Serial , and routing static route on R1-ISP, default route on R2-Central. The following login passwords should all be set to "cisco" no quotes : enable password not secret , console, and Telnet.
Authorized access only. Whenever you configure a Cisco IOS device, be sure to save your configuration. For the server, enable DNS services, use the domain name eagle-server. As you work, use "Check Results" to see what components still need to be configured. If you want more practice, use "Reset Activity" and re-time yourself doing the entire configuration again. It is a good practice to test connectivity through ping and Telnet, and to examine routing tables.
California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.
This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information.
This privacy statement applies solely to information collected by this web site. Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.
We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements.
If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions. All rights reserved. Cisco Press. Join Sign In. View Larger Image.
Part of the Course Booklets series. Book Sorry, this book is no longer in print. Not for Sale. Description Sample Content Updates. Sample Pages Download the sample pages includes Chapter 3. Submit Errata. Overview Pearson Education, Inc. Simulate the routing and switching process as if you are working with real physical devices. Network Fundamentals File size: Routing Protocols and Concepts File size: The CCNA is valid for three years when recertification is required. The loopback address is not set.
The encapsulation type is mismatched. A cable is not attached to the interface. Keepalive messages are not being received. The interface is administratively shut down. Tuesday, August 8, Cisco Packet Tracer 7. August 08, comments.
Use Packet Tracer to:. June 10, May 02, Software. October 28, 10 comments. When a violation is detected, the port will go into err-disable mod. There have been 11 security violations since the last reload.
The port is currently in the shutdown state. Read more ». October 28, 2 comments. Layer 2. Layer 4. Layer 5. Layer 6. Older Posts Home. Subscribe to: Posts Atom. Social Profiles. Popular Tags Blog Archives. SBA 1. SBA 2.
0コメント